Bump It Bot

🚀 Bump It Bot

The Bump It feature on MemeTools is a stealth visibility tool tailored for Pump.fun tokens. It creates controlled buy activity across multiple wallets — either as single or multi-wallet operations — with randomized delays to simulate real demand and push your token to the top of the Pump.fun trending list.

---

🔍 Overview

The Bump It Bot allows you to:

• Simulate real user demand via scheduled buy bursts

• Execute multiple buys with custom delay and slippage

• Maintain consistent visibility at minimal cost

• Run buys from either a single wallet or all wallets

• Use Jito for same-block efficiency and success rate

---

🧠 Key Features

• ✅ Same-block buy clustering (via Jito)

• 🔄 Configurable min/max delays (natural pacing)

• 💸 Minimal SOL requirement (as low as 0.0001 SOL)

• 👥 Works with all wallets or target a single wallet

• 🔧 Full control over slippage, tip, and wallet behavior

---

📋 Requirements

• Valid Pump.fun token contract address

• Wallet(s) funded with enough SOL (0.1-0.2 SOL recommended per wallet)

---

⚙️ Setup Guide

1. Token Import

1. Navigate to Pump.fun

2. Click Add Token

3. Enter your token’s contract address

4. Hit Add

2. Wallet Setup

• Use the Wallets tab to generate wallets

• Fund them with SOL (based on number of bumps)

• Suggested: 0.1–0.2 SOL per wallet

---

🛠 Bump It Settings

Setting	Description
Min/Max Buy (SOL)	Sets the bump buy range (e.g., 0.01 SOL)
Min/Max Delay (ms)	Randomized delay between each buy (e.g., 8000–10000 ms)
Tip Amount (SOL)	Recommended: 0.001 to increase transaction speed
Slippage (%)	Suggested: 10% to avoid failures
Number of Buys	Total buys executed during the cycle (1–3)
RPC / Jito	Use Jito for higher priority and bundling
Bump Mode	Choose between:

• All Wallets: Each wallet bumps

• Single Wallet: One wallet executes all buys | | Select Wallet | Used only when "Single Wallet" is selected |

---

✋ Sell Settings (Optional)

Configure follow-up sells after bumps.

Single Sell

• Set Tip Amount and Slippage

• Choose RPC / Jito

• Optional Exchange Obfuscation: Bullx / Gmgn / Photon

Sell All & Emergency Sell

• Sells all tokens across wallets

• Instant panic-exit supported with Emergency Sell All

---

🧪 Operation Guide

Starting Bump It

1. Configure your bump settings

2. Choose between All Wallets or Single Wallet

3. Enable Jito (optional but recommended)

4. Press Start

5. Watch your token appear on Pump.fun trending

---

💡 Optimization Tips

Strategy	Recommendation
Visibility	Use consistent bumps every 10–20s
Delay Strategy	8s–10s delays look more human
Cost Control	0.01–0.1 SOL keeps gas low (Amount needs to be greater than 0.01 to show on pumpfun home page)
Slippage	10% for volatile launches
Jito	Improves tx priority; especially effective for back-to-back bumps

---

💼 Best Practices

Area	Tip
Wallet Management	Keep 1–5 wallets funded for rolling bumps
Slippage	10–12% recommended for fast launches
Delay Window	Avoid uniform delays to appear less bot-like
Gas Monitoring	Watch SOL balance to sustain longer sessions
Visibility Strategy	Run bumps when Pump.fun traffic is high

---

❗ Important Notes

• Amount above 0.0001 SOL does not affect bump visibility

• Only Amounts above 0.01 SOL show on pumpfun page

• Only frequency and consistency of bumps matter

• Jito is highly recommended to prevent tx failure under load

• Use Exchange Obfuscation to hide wallet activity from public explorers

---

🔧 Troubleshooting

Issue	Solution
No bump visible	Check if min buy = 0.01+ SOL
Tx failed	Increase slippage or use Jito
Stuck in pending	Lower delay or reduce # of wallets
Excessive gas use	Increase min delay or lower buy count

---

🎥 Tutorial Coming Soon...

A full video walkthrough will be available on our YouTube channel covering:

• Single vs All Wallet strategy

• Jito vs RPC differences

• Real-world bump strategies